Thank you very much SFFT!
I'll wait for your good news.

Thanks for your reply SFFT:D
Do you mean the "3dfxvs2k.inf"?
I think I don't have the skill to modify the file...

Hope to see the new SFFT driver!

Almost over a year...
I still can't figure it out.

Is anyone know my problem?

Hi everyone!
I'm using Voodoo5 5500 AGP and SFFT 1.0 driver, and the 3dfx Tools version is 2.6.2.116
But in the "3dfx Tools Hub" it doesn't have the "3dfx info" tag. And in the "3dfx Tools Manager" also not have the 3dfx Info.
What should I do to enable the 3dfx Info?

Image Insert:

26.03 KB


Image Insert:

38.66 KB

Hi everyone!:)
I have a serious problem.
When I use the new SFFT 1.1 driver, my hard disk will make strang sound and then the system crashed. Also hardly boot into windows. But when I use the SFFT 1.0, it was in good condition. I use the HD TUNE to check my hard disk but is was fine. Can anyone tell me what's going on? By the way, please forgive my broken English...OTL[]

My system:
CPU: Intel Celeon 2.66 GHz
MB: GA-8SR533P
RAM: 768MB DDR266
VGA: Voodoo5 5500 AGP
HD: Seagate ST320034A 20GB
OS: Win XP Pro SP3

WOW!!
that is amazing!
how do you make the ram chips on the board??

QuoteOriginally posted by charly204

Hi!!
What software should I use to se a TV on Voodoo3 3500TV?
Is the software have multi language?.........(Like Chinese?)

Should I use a connector or something to link my sound card
with Voodoo card so that I can hear the TV sound?

Thanks!!

Sorry, typing mistake.
I mean to watch TV with Voodoo3 3500TV.

Hi!!
What software should I use to se a TV on Voodoo3 3500TV?
Is the software have multi language?.........(Like Chinese?)

Should I use a connector or something to link my sound card
with Voodoo card so that I can hear the TV sound?

Thanks!!

QuoteOriginally posted by Chips

Yes, I used the "1.18PCIDV" that I download from "http://welcome.to/3dfxbios" too.

Instructions are at http://welcome.to/3dfxbios as well.

DVI works great, but you can't use both the DVI and the SVGA at the same time (i.e. 2 monitors).

Put the monitor on the AGP card first so you can see what you are doing when you flash.

After you get the "flash successful" message, put the monitor on the PCI card and remove the AGP card.  Simple!

Thanks for your reply!!
I'll try it when I get the card these days.
I'm so excited!!

Regards,
Charly

QuoteOriginally posted by Chips

Um, yes and just don't worry about the problems I had in that thread PS47 has referenced - that card was DEAD so that was the real problem.

I purchased another MAC PCI Voodoo 5 5500 the other day and it flashed fine - even the DVI works!  You just have to ensure you use the version 1.18 BIOS.

I placed that vard in a Abit BE6 mobo with a PIII-500 running XP and the AmigaMerlin 3.1 drivers and I'm getting 40-60fps on Unreal Tournament!

Also, don't worry too much if the flash program locks up half way through programming the EEPROM - just reboot the PC and try again - it really is failsafe.

Hi there!!
So if I flash the V1.18 BOIS then I can use it on PC??
Can I use the file "1.18PCIDV" that I download from "http://welcome.to/3dfxbios"??
Does the DVI works well?
I have some questions:
My mainboard is GA-7N700L with a ATI R9700 on AGP8X,
if I put a VoodooMAC on a pci slot, which card should I link my monitor?
And how to flash the BIOS?

My English is poor, hope you can understand.
Regards,
Charly

Hello!!
If I had a Voodoo Mac 5500 PCI, can it use on a X86 PC??
If it can, how??

Regards,
Charly